Archives for posts with tag: ARB

.
I had front and rear ARB Air Lockers installed on our Montero last year. Since we were sailing all of last summer, I haven’t had a chance to try them out on the trail yet, something I’ll rectify soon.

Until I get that post up, you might be interested in checking out how an air locker is actually installed. Jonathan Hanson from Overland Tech & Travel recently had one installed on his Tacoma and filmed the proceedings. Towards the end of the video, there’s some excellent under-the-truck footage showing them in action.

The video comprises “Part 2” of the process. He also wrote about “Part 1,” installing the compressor and air lines to the run the locker.

Links:
Overland Tech & Travel: Installing an ARB Diff Lock, Part 1
Overland Tech & Travel: Installing an ARB Diff Lock, Part 2

00505_3AYkIPtEii_600x450

There’s a very nicely built FJ60 Land Cruiser for sale in Los Angeles right now. This one has ditched the inline six in favor of a CARB-legal, Chevy 350 V-8 crate motor. The suspension has been upgraded as well to Fox 2.0 reservoir shocks. Other highlights: on-board air with a 2.5-gallon accumulator tank, dual batteries, rear diff. lock. The list goes on.

This FJ60 has 320k miles on the body, 20k on the motor and drivetrain. It’s located in Claremont, California, and is being offered for $21,000.

See the rest of the post for a bunch of photos and the full ad text.

Link trail: Bring a Trailer > 1987 FJ-60 Land Cruiser on Craigslist Read the rest of this entry »

P1080009
I’ve been very happy with my ARB Bull Bar bumper and its on-board turn signals, except for the fact that they’re not waterproof. Every now and again I’ll drive the truck through a stream, which inevitably rusts out the bulb sockets, corrodes the contacts, makes the bulb hard to change, and sometimes cause the light to fail.

My solution: waterproof the lenses.

The first thing I did was order a set of replacement lights. My friend Greg tipped me off that they’re the same lights as used on the Mark 1 VW Golf/Rabbit, so they’re easy to get. You can find them here at German Auto Parts. Read the rest of this entry »

12
Photo: Bruce Dorn

Expedition Portal does a nice job of covering ARB’s latest Jeep Wrangler build with a good write-up and a gorgeous set of photos by Bruce Dorn.

Check out the article here: VFOTW: ARB-built Jeep Wrangler

DSC_0112
Read the whole post here.

This is a “Spotted” post but in this case the seller of this beautifully restored FJ45 Troopy spotted me (or the site rather). It’s WCXC’s first seller submission. Here’s the story:

The seller states that this right-hand-drive, 1984 Toyota Land Cruiser FJ45 Troopy started its life in Australia where it racked up only 127,000 km (~79, 400 miles). In 2011, it was legally imported into the U.S. and given a ground-up, frame-off restoration during which the frame and body were stripped, chemical dipped, and epoxy sealed. The frame was then painted with POR-15, and the body got a fresh respray. Truck has clocked 600 km (~375 miles) since then.

The seller also reports that the engine, the venerable 4.2-liter 2F, was rebuilt, balanced, and blueprinted. A new H55F, 5-speed manual transmission was fitted and mated to custom drive shafts. The suspension is an Old Man Emu system, fitted with heavy springs, and greasable shackles and spring pins. The addition of custom sway bars are said to virtually eliminate body roll while cornering. The seller further reports that the axles, differentials and transfer case have all been refreshed with new Toyota parts. Six new 33″ BFGs round out the picture — no pun intended.

Up front, the ARB bull bar is ready for your choice of winch. Out back, a dual swing-away bumper, carries two spares and a Hi-Lift jack (not pictured but said to be included). The roof and doors are removable.

Perhaps the biggest change from stock is the conversion to a dual-fuel system, meaning the truck can run on propane or gasoline. The big advantage of propane is significantly reduced vehicle emissions. Cleaner burning fuel also means a cleaner, longer lasting engine. On the downside, propane packs about 25% less power per gallon than gasoline does. It also sells for about 25% less than gasoline, based on national averages. According to Petersen’s 4Wheel & Offroad propane’s relative lack of punch should only result in a 10% drop in mileage. But a 10% mileage loss at a 25% savings means you’ll still come out ahead. With 12 gallons of gasoline, and 15 gallons of propane on board, the range should be an improvement over the stock 22 gallon tank.

The seller goes on to say that throughout the $72,000 restoration, every nut, bolt, seal, and bearing on the truck was replaced — nothing was left untouched. The result is an almost 30-year-old truck that looks like it just rolled off the showroom floor.

The cost of this beige beauty with comfortable seating for eleven? Significantly less than cost of the restoration at $55,000. Given what restored FJ40s have been selling for at auction lately, this Troopy seems like quite a deal.

Click here to email the seller directly. The truck is located in northern Colorado.

Link resources: Photobucket Gallery

Don’t miss all the photos after the jump. Read the rest of this entry »


Here’s a very nicely equipped, relatively low mileage, 4×4 Isuzu Pickup that’s ready for any off-road adventure. It has a full exoskeleton and rack, Old Man Emu suspension, a winch, ARB locking differentials, and brake and transfer case upgrades. Very nice. It even has a 5-speed, a rare find in “recent” off-road vehicles.

The seller is doing an interesting thing by offering the truck for a variable price of $5,000 – $9,000, depending on how much of the equipment you’d like to leave on the truck with the purchase. If you’d like it all, hurry before he parts it out. You could never build this truck for the asking price.

Link Trail: Expo Forums

Read the rest of this entry »


All photos: Gregory McDonald

I’d been wanting an extra margin of water fording safety and a cleaner intake source than under the fender well, so I ordered an ARB Safari Snorkel. A couple of weekends ago my friend Greg — awesome guy that he is — came up to help me install it. It worked out pretty well and took about 5 or 6 hours from start to finish (including a trip to the hardware store for last minute supplies).

If you install one yourself here’s a list of things you’ll need. Read through your instructions fully before you go to the hardware store to get supplies. I didn’t, hence the extra trip.

Apart from the standard tools, you’ll need:

• an 86mm (3-3/8″) hole saw (this may be different for your truck)
• Loctite
• drills up to 1/2″ diameter (the instructions call for larger but if you follow this method, you won’t need them)
• silicon sealer
• ratcheting box wrench (to tighten the nuts inside the fender well without removing the fender)
• a step drill, if you already have one (they’re about $50 so I just used a series of drills)

Here’s the biggest tip of the whole exercise: use the template only to drill the big, 86mm hole. Mark the small, snorkel bolt holes as well but use the bolts themselves to determine their exact positions. The template may not be accurate — it wasn’t for us. Use the same method for determining the positions of the A-pillar holes and you’ll be dead on.

Be sure to follow along with your instructions, if you do this yourself. I’m only going into a general level of detail in this post.

Read the rest of this entry »



I found a pretty cool solution for mounting a Hi-Lift jack to an ARB bumper using a pair of Chauvet clamps. They’re rated to support a load of 660 lbs each. Best of all they’re about half as expensive as any other solution I’ve found.

Read the rest of this entry »